How to Make your dryer work better

How to Make your dryer work better

 

Have you ever finished drying a load of clothes only to find that they were still wet?

No one likes being in that situation.

Not only do you have to run the dryer again, but you also have to pay for the electricity or gas that it uses.

We want to help you save time and money, so in this article, we’ll tell you how to keep your dryer running well.

Tip 1: Put your clothes in order

Sorting your clothes by size can help your dryer work better.

Separate the smaller things, like underwear, from the bigger things, like towels and sheets.

Check the user guide that came with your dryer for instructions on how to set it up for the different types of clothes you’re drying.

 

Tip #2: Clean out your lint filter

Keeping your lint filter clean is one of the easiest and most important things you can do.

This lint filter gets all the air that goes through your dryer.

If it gets clogged, the appliance won’t work as well and it will take longer for the clothes to dry.

A clogged filter can also cause the dryer to get hotter, which could hurt your clothes and make the lint a fire risk.

If your filter is broken or gone (maybe it went with the missing socks? ), you should replace it because it is an important part of your dryer.

Tip #3: Keep your dryer vents clean.

Even if you clean the lint filter often, some stuff will still get into the vents.

You should check the vent at the back of your dryer every so often to see if there are any signs of buildup.

How you have your vents set up can also make a big difference.

Flexible plastic tubing is very common, but its ridges can catch lint and make it hard to move.

The plastic vents can also be very fragile and break easily if they are bent or cracked.

If the tubing is bent, it can block the flow of air, which makes your dryer less effective.

We’d suggest making your vents out of something other than plastic.

Tip #4: Keep the vent caps in place.

Next, we’ll go outside to check out the vent cap on the outside of your house.

Usually, there are two kinds: a single flap and multiple flaps, also called louvered flaps.

You want to make sure that the flaps close when there is no airflow and open fully and freely when your dryer is running.

If there is lint in the vent, it needs to be cleaned out so that it can work properly.

you can clean out your dryer vent system completely.

If you put a screen or rodent guard over the vent cap, it can get clogged with lint and dust, which makes it hard for air to get in and out.

 

Tip #5: Check the door gasket

When your dryer door is closed, the gasket makes a tight seal so that the hot air stays inside and the room-temperature air stays outside.

If there are tears or missing pieces in the door gasket, the seal is broken and the gasket should be replaced.

If hot air gets out or cool air gets sucked in, your dryer won’t work as well, and it may take longer or work harder to dry your clothes.

 

Tip #6: Take care of heating elements

The inlet duct assembly is found inside the drum of your dryer.

The surface can get very hot, and if certain types of fabric touch it, they will melt. If something has melted onto the duct, it can make the surface rough, which can hurt your clothes even more.

After the dryer has cooled down, check this part and clean it if it needs to be.

Cleaning Your Dryer Vent

cleaning your dryer vent

 

in this post, we will talk about cleaning your dryer vent. It’s important to keep your dryer vent clean for a few reasons.

  • Your dryer will operate more effectively

and you will be saving money and the environment, the cleaner your vent is.

  • It is critical from a safety standpoint as well.

Lint buildup within the dryer, which is a severe fire hazard, is also produced by lint accumulation in the dryer vents.

 

Generally speaking, you should check and clean your dryer vents once a year; however, if you use your dryer more frequently than usual, you might want to clean it every six months.

The steps we took are described below.

Step 1: Turn off the power and move the dryer

You must turn off the power before attempting to move the dryer.

You should check the venting to make sure you won’t damage it when you pull the dryer forward now that the power has been turned off.

Step 2: Remove the dryer’s vent.

You may now access the dryer’s back vent because the dryer has been moved forward.

If there is a buildup of trash or lint, remove the vent with your hands and look inside.

Additionally, you should look inside the dryer’s opening in the back.

Check once more to make sure there isn’t a lint or particle buildup.

Step 3. Examine the inlet grills.

You should disassemble the dryer if you see a significant amount of lint accumulation on the inlet grills because it’s likely that some of the lint has been drawn back into that area and somewhere near the heating source, which could pose a fire risk.

To get rid of the lint, you must remove the grate.

Step 4: Turn on the clothes dryer

Next, you’ll need to use the dryer’s air to push out any lint that might get loose when we clean the ductwork outside.

Depending on what you use to clean the ductwork, you may want to add a device that stops the brush from going into the dryer.

It is attached to the dryer’s outlet duct on the back, and the duct is then reconnected to it.

To get rid of the loosening lint, you will have to turn on the dryer and push the lint out the side of the house.

Step 5: Put the Rotary Brush together.

Using a rotary brush is one of the most common ways to clean out a dryer vent.

You can easily get these from a rental company or a nearby hardware store.

It is a 4-inch brush that fits inside the ductwork and can be turned with a portable drill.

Depending on the method, you may want to vacuum while you clean.

If so, you will need to attach an adapter to the brush, vent, and vacuum. It could get very dusty, so a mask and eye protection are recommended.

Step 6: Take off the ventilation cap

If your vent cap has a louvered style, you will need to take that off before putting the brush in.

If there is only one flap, all you have to do is lift it up and slide the brush in. If you want to use a vacuum, you will need to take the cap off completely.

This is also a great time to check the vent cap to see if it needs to be fixed or replaced.

If it’s broken, it could let cold air into the house or make it easy for a rodent to get inside the house

 

Step 7: Clean the vents and ducts

After taking off the cap, put the brush into the ductwork.

If you know how long the ductwork is, you might want to add an extension to make the brush longer.

When you connect an attachment, make sure it’s good and tight, because you don’t want it to fall apart while it’s in the vent.

You’ll need a pair of pliers and some electrical tape to make sure it fits well.

You can now connect the wand to your portable drill by turning it clockwise.

 

Step 8: Put the vent cap back on and caulk it.

After using your rotary brush to clean out the ductwork, you can put the vent cap back on.

If you are putting on a new vent cap or giving yours some maintenance, you might want to caulk around the edges to keep water from getting in.

 

How to Replace a Drum Baffle in a Dryer

The Drum Baffles are an important component in your dryer, but do you know what exactly they are?

Every time you put clothing in the dryer, you interact with them, but perhaps you’ve never known their full name.

The sets of “fins” inside the drum of your dryer that are called “baffles” are typically three or four in number and are evenly spaced out.

During the tumbling process of the dryer, they assist with airflow and fluff up your garments.

They accomplish this by removing clothing off the dryer’s side and placing it in the airflow.

Without baffles, your clothing would remain clumped together in the dryer and wouldn’t dry completely.

You risk having your clothing snagged or caught by them if they get loosened or broken.

The baffles on a drum may occasionally break free or separate from it after prolonged use or drying of goods like shoes.

To avoid permanently harming your clothing or your drum, it’s crucial that you take care of that issue as soon as you can.

It’s time to inspect one of your baffles if you notice that it has gotten loose or is beginning to rattle.

The procedure for inspecting and repairing your baffles should be comparable, even though the dryer we’re using for our demonstration might not be the same model as yours. Before doing any repairs on your dryer, make sure to turn off the power to it.

If your dryer is gas-heated, you should also turn off the gas supply.

You can watch the video below to follow along while we do this repair.

To access the drum, remove parts.

To access the hinges, the dryer door must first be opened. Lift the door to remove it completely from your dryer by removing the screws holding the hinges to the dryer’s body.

Call Us

Place the door away from your work area in a secure location.

The screws holding the front panels in place must then be removed. We can then access the mounting brackets for the main top once those are out of the way.

Once those are gone, we may lift the dryer’s top, giving us access to the drum’s exterior.

The Baffles: Examine, Remove, and Replace

Now that the main top has been raised, we may rotate the dryer drum such that the damaged baffle is located at the dryer’s “top.”

We can take out the screws keeping the baffle in place from the outside of the drum.

All you need to do to fix a baffle that has just gotten loose is tighten the screws. You will need to replace the baffle, though, if it is broken off completely or is otherwise damaged.

In our case, we found that the screw holes were stripped, making it impossible for us to tighten our baffle to the drum again.

In order to remove the baffle, support it within the dryer with one hand (to prevent it from dropping and potentially harming the drum), then remove the two screws from the outer drum. Now is the time to check the other dryer baffles for damage or to tighten them.

Use a larger washer when replacing if the holes on the drum have any damage to ensure they stay nice and tight.

Close up The Dryer

It’s time to put your dryer back together once you’ve examined, changed, and tightened up each of the baffles.

Lower the main top slowly, making sure it clicks into place.

The mounting brackets, front panels, and door hinges need all be replaced.

Keep an eye on any loose baffles to prevent the tearing of your clothing or damage to your dryer.

Be aware of the condition of your baffles. Aim to keep heavy, bulky goods like sneakers off the dryer’s baffles so they don’t fracture or break.

Call Us

Common Broken Dryer Symptoms

Common Broken Dryer Symptoms

  • Noisy

Learn how to repair your dryer when it’s making noise by troubleshooting common problems and parts like bearings, seals or worn belts.

  • Will not start

Find out how to fix a dryer that will not start, by checking a few key components, such as the heating element, high limit thermostat, or cycling thermostat

  • No heat or not enough heat

When your dryer is not producing any heat or not enough heat to dry clothes, inspect common parts like heating elements or fuses.

  • Will not tumble

When your dryer won’t tumble or turn, look at common parts to see if they may be worn or defective, like switches or belts.

  • The timer will not advance

Find out what can cause your dryer’s timer to stop advancing by using our list of troubleshooting tips and repair parts like cycling thermostats or timer motors.

 

  • Takes too long to dry

If your dryer is taking too long to dry your clothes,
troubleshoot common problem parts like coils, thermostats, and heating elements.

  • Will not shut off

Learn how to repair your dryer when it won’t shut off, by checking the most common parts that cause this symptom, like door switches or timers.

  • Shuts off too soon

Find out how to repair your dryer when it shuts off too soon on the auto dry setting by checking a few key components like thermostats, heating coils, or fuses.

  • Too hot

your dryer is too hot you should start by looking at common parts to see if they may be worn or defective, like thermostats or fuses.

 

Call Us

 

get a free estimate today

 

parts

parts

  •   Repairclinic – This extensive website sells dryer parts, they claim to

    have more than 4+ Million Appliances, Equipment, & HVAC parts in stock for fast shipping

  • Partselect.com
  • AppliancePartspros.com

dryer heater

Heat loss, or even too much heat in some situations, is a typical issue with electric dryers.

You most certainly have a burned-out heating coil if all of your heat is gone.

Similar to toaster heating coils, dryer heating coils have a set lifespan and eventually burn out.

Since a loose element could short out against the dryer cabinet and start a fire if your heat goes out, you should stop using it and unhook your dryer right away until a repair can be completed.

The overheating of the clothes dryer is another hazardous heat-related issue.

You may even be able to see the blazing element at the dryer’s back in this situation, and the top may become extremely hot.

In this situation, you have a shorted-out element, which has the potential to spark a fire. So as you could expect, you need to stop using and disconnect an overheating dryer right away.

Depending on the model, access to the dryer heating unit may differ. Some of the more popular access techniques are covered in the stages below.

Disconnecting the power cord is Step 0!

 

Step 1A: Remove the access panel for the heating units at the back of the dryer.

One just needs to remove 8–10 sheet metal screws to access the heater unit on some models, such as the Maytag Centennial, which has the heater unit on the dryer’s back.

After a few more screws are removed, the heating unit may be removed and replaced by simply unhooking the old unit’s cables and attaching them to the new one.

Other versions can require you to remove the top, a bracket from inside the cabinet, a rear panel, and other components.

 

 

Step 1B – For heating units on the inside of the cabinet.

For some types, you have to take off the top and the drum to get to the heating element. Examine Drum Removal and Top Removal. The dryer coil or a compartment containing the dryer coil will be visible once the drum has been removed.

 

 

Reassemble the dryer in Step 2.

Reassemble your dryer by following all the previous steps you completed to fix or replace the heating unit in reverse.

dryer belt replacement

dryer belt replacement

Important Information

If the dryer produces a lot of noise when you turn it on or the drum won’t spin, replace the dryer belt.

Depending on the model, disassembling your dryer may be slightly different.

However, look for fasteners and screws around the seams where your dryer’s top and front panels join.

The replacement belt should be zigzagged around the two pulleys at the base of the machine.

 

Disconnecting the power cord is Step 0!

Step 1: Release the spring clips and raise the top.

The process of removing the top of a dryer nearly always entails depressing two spring clips in the dryer’s front and raising upward, regardless of the dryer’s brand or type. In some designs, such as the Maytag dryer visible in the bottom left image, you might also need to remove a few screws holding the top to a lint filter.

 

 

Step 2: Either take the top off or give it some support.

The top of many versions will contain control units connected via numerous wires. In order to avoid damaging or even shearing off wires, this sort of dryer requires that the top be supported vertically from above, as seen in the lower left photo! Other variants, such as the Kenmore model on the right, just require the removal of a ground wire before the top may be completely removed from two hinges.

 

Top Unhook Wires Secured

 

You can visually inspect the belt and check for lint buildup with the lid off. To prevent a fire hazard, you should remove the front and drum of the appliance if you notice lint buildup.

 

we highly recommend checking out this link about How to Change a Clothes Dryer Belt

 

 

Call Us